Los artículos de ayuda existen en alemán e inglés. Aquí los lees en inglés.
Instalación
How do I check on my website what the tracking script does?
Use the debug panel. Under “Setup → Live test” you create a debug link that is valid for one hour. Open your website with it, and a panel in the top right shows whether the script runs, what the consent status is, which events it sent and how Metrunio responded. Only people who open the link see it.
Is there a debugger for tracking right on the website?
How to open the panel
- 01Open “Setup” and the “Live test” card there.
- 02Under “Debug panel on your website”, choose “Create debug link”.
- 03“Open website with debug panel” opens the start address of your website with the link. For another page, copy the link and change the path; keep the part with metrunio-debug.
- 04Make a choice in the banner and click through, for example up to the order. The panel refreshes every second.
What the panel shows
| Section | What you see |
|---|---|
| Tracking script | Whether it runs, site ID, measurement address, test or live mode, waiting events and whether the session has been counted. If it does not start, the reason is shown, for example a placeholder instead of the write key. |
| Consent | The decision as the script knows it, separately for analytics and marketing. With the consent bridge, also the detected tool, the entries it looks for and notes as in the consent check. |
| Events | Every event on this page with its state: waiting for the decision, dropped, accepted, or rejected with an error code. |
| Campaign | The campaign identifiers in the address, that is UTM parameters and the click ID with its platform, and what the session started with. |
Good to know
- The link is valid for one hour and only for the website you created it for. If the page runs a script with another site ID, the panel says so and shows nothing else.
- A bare parameter such as metrunio-debug=1 shows nothing. Visitors to your website never see the panel, and without a valid link the script does not load it.
- The panel stays open as you click on, because the script carries the link into the address of the next page. If your website sends no referrer or the checkout is on another domain, open the copied link on the page you want to check.
- The panel only reads what the script does in your browser. It sends nothing and stores nothing on your device. The link does not end up in your data either: the script removes it from the address and the referrer before it sends events.
- If the Content Security Policy of your website does not allow the measurement address, the panel does not load, and the browser console reports DEBUG_PANEL_UNAVAILABLE. The tracking script itself needs the same permission.
- On German-language pages the panel shows German, otherwise English.
Note
The debug panel complements the live test. The live test shows in the portal what arrives at Metrunio; the panel shows on the website what happens before that. If nothing arrives in the live test, the panel usually tells you why.
Revisado por última vez el 16 oct 2026
En el portal del cliente
También se pregunta
- Live debugger
- Debug tracking on the website
- Why are no events arriving?
- Does my shop send the order?
- Are my UTM parameters recognised?
- Debug mode for the tracking script
- Debug link expired
Artículos relacionados
- How do I check my consent status?
How do I make sure consent takes effect correctly?
With two checks that show different things. The rule check under “Setup → Consent” runs six cases against your saved setting, without your website. Whether the website reports consent and withdrawal correctly only shows in the live test with real page views: for each signal the time, source and reported consent status.
- How does Metrunio take the decision from my consent tool?
Do I have to call metrunio.setConsent myself if I use Usercentrics, Cookiebot, Complianz, Borlabs Cookie, Real Cookie Banner or another common consent tool?
Through the consent bridge, without you calling
metrunio.setConsentyourself: for thirteen tools this small additional script reads the decision from your banner and passes it to Metrunio, including every later withdrawal. The installation code in the portal contains it as soon as you choose your tool in the consent step, and the Shopware plugin adds it by itself. - What does the setup health centre do?
How do I find out what is missing in my setup?
The health centre runs a diagnosis across your setup and reports every finding with cause, effect, error code and the steps to fix it, rather than just an error message.
- What do the error codes mean?
The collector answers with a code. What does it mean?
Every rejection carries a code together with a title, explanation, data effect and resolution steps. This table lists all codes of the collector and of processing with their meaning.